Water Spot Removal & Protection System

Remove. Reset. Protect.

Want this on repeat? Subscribe & Save 10% with the Season Pass kit → Ships every 2 or 3 months. Skip, pause or cancel anytime.

The complete 3-step cleaning and protection system for stubborn hard water spots, mineral deposits, and water staining on marine gelcoat, painted hulls, glass, and compatible exterior surfaces. Zero Spot breaks down mineral buildup and hard water deposits, Strip-Tide removes remaining contamination and cleaning residue, and Boost Coat restores gloss while adding a protective layer of natural carnauba wax to help reduce future water spotting.

Three products, one process, a spotless and protected finish.

Also fighting a yellow scum line? This same 3-step system handles it. No need to buy both.

What's Included (16 oz each):

• Step 1 – Zero Spot: Marine Water Spot & Mineral Deposit Remover

• Step 2 – Strip-Tide: Heavy-Surfactant Decontamination & Reset Wash

• Step 3 – Boost Coat: Carnauba Wax Protection Spray

How to Use the System

1. Remove water spots with Zero Spot. Work in the shade on a cool surface with appropriate gloves and eye protection. Spray Zero Spot directly onto a clean microfiber towel, not onto the surface. Apply evenly to affected areas, allowing approximately 30 seconds of dwell time to break down hard water spots, calcium deposits, and mineral buildup. Gently wipe away residue with a separate clean microfiber towel. Repeat if necessary for stubborn deposits. Never allow Zero Spot to dry on the surface.

2. Reset the surface with Strip-Tide. Thoroughly rinse the treated area with fresh water. Wash the surface using Strip-Tide diluted at 3–4 oz per 5-gallon bucket of water. Gently agitate with a clean wash mitt to remove remaining mineral residue, old wax, sealants, oils, and surface contamination. Allow 3–5 minutes of dwell time without letting the solution dry, then rinse thoroughly with fresh water to leave the surface clean and ready for protection.

3. Restore gloss and protect with Boost Coat. Once the surface is completely clean and dry, lightly mist Boost Coat directly onto the surface or a clean microfiber towel. Work one section at a time, applying evenly with overlapping passes. Immediately buff with a separate clean microfiber towel until the surface feels slick and develops a deep, glossy finish. Reapply during routine maintenance washes to refresh protection and help reduce future water spotting.

Why This System Works

• Hard Water Spot Removal: Zero Spot targets stubborn calcium deposits, mineral buildup, and water staining that ordinary soaps cannot remove.

• Mineral Deposit Breakdown: Helps dissolve accumulated minerals left behind by hard water, saltwater spray, and repeated washdowns.

• Deep Surface Decontamination: Strip-Tide removes old wax, sealant residue, oils, and remaining surface contamination.

• Restored Gloss & Clarity: Boost Coat enhances the natural depth, shine, and reflective appearance of properly cleaned surfaces.

• Hydrophobic Protection: Natural carnauba wax creates a sacrificial protective layer that encourages water beading and runoff.

• Reduced Future Water Spotting: Protective wax helps make subsequent cleaning easier and reduces the adhesion of everyday contaminants.

• Versatile Marine & Automotive Use: Designed for compatible cured gelcoat, painted surfaces, stainless steel, and exterior glass.

• Professional-Grade Results: Engineered for detailers and boat owners looking to remove existing water spots and maintain a cleaner, better-protected finish.

Important

• For compatible cured marine gelcoat, painted surfaces, and approved exterior materials only. Always spot-test before full application.

• Zero Spot is not suitable for plastic, anodized surfaces, or mirrored glass. Avoid contact with incompatible trim, hardware, and delicate finishes.

• Wear appropriate gloves and eye protection when handling Zero Spot.

• Never mix Zero Spot directly with Strip-Tide or other cleaning chemicals. Thoroughly rinse between applications. Strip-Tide washing removes residue but is not a verified chemical neutralization step unless confirmed through product testing.

• Strip-Tide is designed to remove existing waxes and sealants and may compromise protective coatings. Reapply protection after decontamination.

• Never allow Zero Spot or Strip-Tide to dry on the surface. Avoid hot surfaces and direct sunlight.

• Boost Coat helps reduce future water spotting but does not eliminate mineral deposits caused by hard water. Drying surfaces after washing is still recommended.

• Do not apply Boost Coat to matte finishes, fabric, uncured paint, or non-skid surfaces.

• Follow each product's instructions and SDS for complete safety information.

Eliminate the water spots. Restore the shine. Protect against the next washdown.

Made by detailers. Made in the USA.